Catalytic Transformation of Nitroarenes to Amines over Ba(1-x)SrxTiO3 (0 < x < 1) Perovskites in Water.

This work is focused on the application of lanthanide-free perovskite Ba1-xSrxTiO3 (0 < x < 1) in valorization of toxic pollutants as 4-nitrophenol (4-NPh). The series of perovskites were fabricated by facile, one-step solid-state preparation method and characterized via various techniques: elemental analysis (Inductively Coupled Plasma Optical Emission Spectrometry, ICP-OES), powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and dielectric properties (impedance spectroscopy, IS). The methods confirmed the assumed composition, structure and high purity of the materials. The results showed that substitution of Ba2+ by Sr2+ in the perovskite crystal lattice influenced the dielectric properties of samples and the size of the grains. The absorption and catalytic properties of Ba(1-x)SrxTiO3 (0 < x < 1) series were evaluated in reduction of 4-NPh in water using NaBH4 as reducing agent. No adsorption of 4-NPh was found for all the materials during 180 min of contact (experiment without reducing agent), and the best catalytic performance was found for the Ba(1-x)SrxTiO3 (x = 0.3) sample. The catalytic transformation of 4-NPh to 4-APh follows a pseudo-first-order model, and the catalysts can be easily regenerated via mild annealing (300 °C).

Graphene-Type Materials for the Dispersive Solid-Phase Extraction Step in the QuEChERS Method for the Extraction of Brominated Flame Retardants from Capsicum Cultivars.

A new application of graphene-type materials as an alternative cleanup sorbent in a quick, easy, cheap, effective, rugged, and safe (QuEChERS) procedure combined with GC-ECD/GC-MS/GC-MS/MS detection was successfully used for the simultaneous analysis of 12 brominated flame retardants in Capsicum cultivar samples. The chemical, structural, and morphological properties of the graphene-type materials were evaluated. The materials exhibited good adsorption capability of matrix interferents without compromising the extraction efficiency of target analytes when compared with other cleanups using commercial sorbents. Under optimal conditions, excellent recoveries were obtained, ranging from 90 to 108% with relative standard deviations of <14%. The developed method showed good linearity with a correlation coefficient above 0.9927, and the limits of quantification were in the range of 0.35-0.82 µg/kg. The developed QuEChERS procedure using reduced graphite oxide (rGO) combined with GC/MS was successfully applied in 20 samples, and the pentabromotoluene residues were quantified in two samples.

Solar Light-Induced Methylene Blue Removal over TiO2/AC Composites and Photocatalytic Regeneration.

TiO2-containing photocatalysts, which combine TiO2 with carbon-based materials, are promising materials for wastewater treatment due to synergistic photodegradation and adsorption phenomena. In this work, TiO2/AC composites were produced by the in situ immobilization of TiO2 nanoparticles over activated carbon (AC) derived from spent coffee grains, using different TiO2/AC proportions. The TiO2/AC composites were tested as adsorbents (dark) and as photocatalysts in a combined adsorption+photocatalytic process (solar irradiation) for methylene blue (MB) removal from ultrapure water, and from a secondary effluent (SecEf) of an urban wastewater treatment plant. All the materials were characterized by XRD (X-ray powder diffraction), N2 adsorption-desorption isotherms at -196 °C, SEM (scanning electron microscopy), UV-Vis diffuse reflectance, FTIR (Fourier-transform infrared spectroscopy), TPD (temperature programmed desorption), XPS (X-ray photoelectron spectroscopy) and TGA (thermogravimetric analysis). The TiAC60 (60% C) composite presented the lowest band gap (1.84 eV), while, for TiAC29 (29% C), the value was close to that of bare TiO2 (3.18 vs. 3.17 eV). Regardless of the material, the solar irradiation improved the percentage of MB discolouration when compared to adsorption in dark conditions. In the case of simultaneous adsorption+photocatalytic assays performed in ultrapure water, TiAC29 presented the fastest MB removal. Nevertheless, both TiAC29 and TiAC60 led to excellent MB removal percentages (96.1-98.1%). UV-induced photoregeneration was a promising strategy to recover the adsorption capacity of the materials, especially for TiAC60 and AC (>95%). When the assays were performed in SecEf, all the materials promoted discolouration percentages close to those obtained in ultrapure water. The bulk water parameters revealed that TiAC60 allowed the removal of a higher amount of MB, associated with the overall improvement of the SecEf quality.

Evaluation of Rhodamine B Photocatalytic Degradation over BaTiO3-MnO2 Ceramic Materials.

Ferroelectric ceramics (BaTiO3_MnO2) with different Mn admixtures were prepared using solid-state synthesis. Elemental analysis, powder X-ray diffraction, scanning electron microscopy, Fourier-transform infrared spectroscopy, and impedance spectroscopy confirmed that the BaTiO3 and MnO2 coexisted in the ceramics. In addition, the high purity and homogeneity of the element distributions in the ceramic samples were confirmed. The adsorptive and photocatalytic properties of the BaTiO3 (reference sample, BTO) and BaTiO3_MnO2 materials (BTO_x, where x is wt.% of MnO2 and x = 1, 2 or 3, denoted as BTO_1, BTO_2 and BTO_3, respectively) were evaluated using Rhodamine B (RhB) as the model dye in a photocatalytic chamber equipped with a UV lamp (15 W) in the absence of additional oxidants and (co)catalysts. No adsorption of RhB dye was found for all the materials during 360 min (dark experiment). All samples were photocatalytically active, and the best results were observed for the BTO_3 material, where RhB was 70% removed from aqueous solution during 360 min of irradiation. The photodegradation of RhB in the presence of MnO2-modified BTO ceramics followed a pseudo-first order model and the rate constant of BTO_3 was about 10 times higher than that of BTO, 2 times that of BTO_2, and 1.5 times that of BTO_1. The photocatalysts could be successfully reused after thermal activation.

Organo-Laponites as novel mesoporous supports for manganese(III) salen catalysts.

A Mn(III) salen complex was immobilized onto the Laponite surface using three different methodologies: method A, direct immobilization of the complex on the parent Laponite; method B, covalent anchoring through cyanuric chloride (CC); and method C, covalent anchoring through CC into a 3-aminopropyl)triethoxysilane (APTES) modified Laponite. All of the materials were characterized by FTIR, XPS, thermogravimetry, XRD, and nitrogen isotherms at 77 K, to gather information on the modifications introduced by the organo spacers within the Laponite surface, as well as on the anchored complex integrity; the Mn based materials were screened in the heterogeneous epoxidation of styrene. The results have shown that the immobilization of the manganese(III) salen complex by methods B and C have occurred at the edges of the clay particles through the spacers (APTES and CC) that have been anchored onto the Si-OH groups, whereas in method A, the complex is distributed throughout the clay surface, including the interlayer region. Therefore, the manganese loadings on the Laponites were as follows: materials prepared by method A >> method B > method C. All of the heterogeneous catalysts showed high styrene epoxide selectivity, with that prepared by method A showing comparable styrene epoxide selectivity as the homogeneous phase reaction. The styrene epoxide yields decrease in the following order: materials prepared by method A > method B > method C (1st cycles), which parallel the respective support catalytic activity and decreasing of manganese content. The heterogeneous catalysts prepared using methods B and C could be reused at least for four times, with the former exhibiting the most stable catalytic activity, but that prepared by method A showed a significant decrease after two catalytic cycles.